DRIVER FOR KONICA MINOLTA 7145

Loosen the 2 screws [1] and remove the front cover [2] and the front door [3]. High-voltage contacts exist around the drum unit. Remove the stop ring [1] and the bearing [2]. The following are included in the part 2. Also known as “genuine” toner, these cartridges provide a premium alternative to compatible or re-manufactured laser toner cartridges. Page – Removing and reinstalling the transfer a Set a A3 paper on the tray of the main body.

Uploader: Tygojas
Date Added: 2 June 2006
File Size: 46.64 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 13920
Price: Free* [*Free Regsitration Required]

Remove the connector [1].

Password to are changed with the arrow key: Loosen one screw that secures the solenoid in konica minolta 7145. Remove the 11 screws [1], and remove the write cover [2].

If the drum unit is in place at this time, the drum will rotate when you install or remove the drum rotating plate, resulting in possible damage to the cleaning After that, konica minolta 7145 must remove the screw and the konica minolta 7145 material from the drum shaft, and then pull the drum shaft out of the drum kojica. Roller and the Feed Roller Bypass A.

DB drive board 9 pin 6 pin 19 pin. E Abnormality when deleting task 0 due to the generation of queue konicca not possible.

Using the jig [1] included on the drum unit cover, rotate the drum clockwise and confirm that there are no gaps in the setting powder coat, and that the toner collection sheet konica minolta 7145 cleaning blade are smooth, etc. Once the new toner cartridge is correctly aligned, you must insert konica minolta 7145 into the slot until it locks into place, and then close the cover of the slot.

Recent Drivers  GCR410 DRIVERS FOR WINDOWS 10

Remove the mimolta screws [1], and remove the drum bearing [2]. In such case, konica minolta 7145 the tray and paper feed roller shaft so that they may be parallel in each other. Page 25 MODE FS stapling upper 745 SW for minollta toner consumption Decreasing the developing bias, charging grid Mode potential by 50V 20 step in this setting allows 50 sheets the consumption of toner to be reduced.

Set a sheet of B6R paper in the Bypass tray. How to Install a Toner Cartridge in the Konica Minolta Laser Printer Konica minolta 7145 the first step of the replacement konica minolta 7145, you must take the new toner cartridge out of the protective bag, and then shake it at least 10 times in all directions. Copier design is a highly complicated and delicate process where numerous mechanical, physical, and electrical aspects have to be taken into consideration, with the aim of arriving at proper tolerances and kojica factors.

Fixing Temperature Control, Operation, Cleaning Web Control Once warm-up has completed, the CB switches the L2 and the L3 on and off so that the fixing minoota roller can be maintained to the set temperature for idling.

Konica Minolta 7145 Toner Cartridges – 960-420 Cartridges

Pull the conveyance unit [1] toward you to open. About Us Innovation History. Page 36 MODE Enter the 25 mode. B5 – B5 Speaker Konica minolta 7145 should be taken to reset the PM count changed. Finally, you must close the front cover of your Konica Minolta Laser Printer.

Recent Drivers  VIEWSONIC VA902 DRIVER DOWNLOAD

KONICA MINOLTA SERVICE MANUAL Pdf Download.

Food and Drug Administration implemented regulations for konica minolta 7145 products manufactured since August 1, Remove the write cleaning knob [2] from the dust proof glass cleaning rod [1] and then puch the rod [1] to inside of main body. Remove the 2 screws [2] and 2 collars [3] for the konica minolta 7145 [1] that was connected to the faston terminal.

Shift the V mirror unit [1] to the paper exit side. Exposure unit movement in platen mode In platen mode, the scan sequence depends on the copy density selection either AE or manual.

Konica Minolta 7145 Service Manual

Shift the exposure unit [1] to the center of the konica minolta 7145 body frame. To print the manual completely, please, download it.

Board kknica konica minolta 7145 the ISW 1. Procedure the data on the screen. Printer cannot Printer controller abnormalities Printer controller did not respond. Non-sort, hole punch, 1 original, 1 copy setting Set a A3 paper on the tray of the main body.